Go Company

 

Are you hunting for critical information around Tools You Need to Install a New Bathtub ?

Mounting a bathtub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably hard task. If the old tub is readily available, the project can relocate rapidly; if you need to open a wall to eliminate the old bathtub and position the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will require a helper to vacate the old tub and embeded in the new one. Ensure you have qualified on your own for the task as well as are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed project, it is better to take into consideration employing one before you start. Chances are you may need a specialist plumber to make tube connections.
This write-up will help you mount a new bath tub in your restroom if you have currently acquired a new tub and do not require to alter the setup of your previous water system pipes.
Your devices as well as product list ought to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Installment

To start with, the supporting frame provided with the bath must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last setting.

 

 

Removing Old Taps

If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the limited gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will come from the pipes. Once the supply pipes have actually been removed, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before moving on to fit the new faucets, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Mounting the Tub

Making use of both wooden boards under its feet, place the tub in the required position. The wood boards are practical in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the tub till the spirit level reviews degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the proper supply pipe by making a compression sign up with; then do the same for the various other faucet.
Activate the water and also check all joints and new pipework for leakages and tighten them if necessary. Fill up the tub as well as likewise examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub should wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its last position.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washing machines remain in area between the tap and the sink. Protect the faucet in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind must be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bath tub

In the location where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture an inflexible seal, triggering the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the tub is in use. The sealer can crack fairly very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles using waterproof or water-proof adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We were shown that write-up about Tools You Need to Install a New Bathtub from a good friend on another domain. If you appreciated our page plz don't forget to share it. We recognize the value of reading our article about Installing A Bathtub.

Get Offer